Image: Bryn Nelson
By Columnist
msnbc.com
updated 7/21/2008 8:46:35 AM ET 2008-07-21T12:46:35

A sea of potential is lurking just beneath the waves. In a sinuous rubber tube dubbed the Anaconda and in the unusual features of dolphin flukes and humpback whale fins, scientists are looking to the ocean and its inhabitants for a little alternative energy inspiration.

For Frank Fish, humpback whales are inspiring new designs for more efficient windmills and industrial ceiling fans. Why humpbacks? “They actually have these very elongated flippers, about one-third the body length of the animals,” said Fish, a biomechanist at West Chester University in West Chester, Pa.

Along the leading edge of each wing-like flipper, he said, prominent bumps called tubercles modify the flow of water and keep it from stalling. A stall, in either air or water, happens when a wing (or flipper) banks at too high of an angle relative to the oncoming flow, resulting in a dramatic loss of lift. The phenomenon can be catastrophic in airplanes, dropping them from the sky like dead weight.

Humpback fins, however, show that bumpy surfaces can help establish a flow pattern that reduces the likelihood of a stall. Because of the design, the wings can be held at a much higher angle to increase the flow. Fish’s research suggests that at higher angles, the tubercles may actually reduce the drag compared to perfectly smooth wings, flipping conventional engineering theory on its head. Accordingly, Fish sees obvious applications for any lifting, wing-like surface, whether for airplanes or windmills.

Whales and wind turbines
Fish, who presented his research at the Society for Experimental Biology’s annual meeting earlier this month in Marseille, France, has begun applying his work commercially as president of Toronto-based WhalePower. The company’s Web site coyly claims “a million years of field tests” for its humpback-inspired “Tubercle Technology.”

Despite the head start, Fish isn’t quite ready to publish the results with a 30 kilowatt test windmill on Canada’s Prince Edward Island, run by the Wind Energy Institute of Canada. Preliminary tests in wind tunnels, however, have yielded a 4 percent increase in maximum lift, a 40 percent increase in the stall angle and a reduction in drag by as much as 34 percent.

A 4 percent increase in lift may not seem like much, but even small increases can help boost efficiency. Windmills are generally kept far below their maximum lift potential to prevent stalls, which tend to happen asymmetrically so that only one blade falters. The ensuing vibrations can cause a windmill to literally shake itself apart.

Decreasing the attack angle and maximum lift as a precaution means less power generation, but Fish said adding tubercles to the windmill blades requires less of a tradeoff. Beyond the initial test site, Fish would like to scale up the blade design for the larger 3-megawatt wind turbines popping up around the world.

Whales-inspired ceiling fans
If humpback-inspired wind farms are still a few years away, another whale of a design is on tap for industrial ceiling fans by summer’s end.

Stephan Gingras, research and development manager for Seaforth, Ontario-based Envira-North Systems Ltd., said he was initially wary when WhalePower approached his company, one of Canada’s largest industrial fan manufacturers.

“Like everybody else, we were a little bit skeptical,” he said. “What will a whale have to do with blades on fans?”

Plenty, as it turns out. Envira-North’s ceiling fans, varying from 8 to 24 feet in diameter and destined for the likes of aircraft hangars, gymnasiums and shopping malls, can wield up to 10 blades and weigh 500 pounds. The normal angle of attack, or pitch of each blade as it pushes through the air, is about 15 degrees. Adding tubercles to each blade’s leading edge, Gingras said, has allowed the company to increase that angle to 25 degrees, greatly increasing the efficiency.

And as the efficiency increases, costs go down. Currently, a 2 horsepower motor suffices for the biggest fans, which move more than the 380,000 cubic feet every minute. But a new whale-inspired fan in the final stages of testing will push the same volume or more with only four or five blades, cutting about 150 pounds in the process. With a less weighty fan, Gingras said, “maybe we’ll only need 1.5 horsepower.”

Design based on dolphin flukes
For a separate project, Fish’s lab is studying dolphin flukes as inspiration for generating better thrust for boats or submarines. The key is the flexibility of a dolphin’s fluke, or its tail fin.

Fish believes mimicking the fluke’s unusual mechanics could lead to more efficient and flexible propellers. “What we have with dolphin flukes is a wing,” he said. “Instead of that wing simply staying static against a flow, it moves up and down. It just doesn’t wag like the tail of a dog — there’s a joint at the base of the fluke, and it varies the angle of attack.”

If the joint is key to maintaining the best angle of attack and the thrust though the dolphin’s entire stroke cycle, modifications at the tip of the fluke influence the water flow so the animal receives as much lift as possible. Fluke tips, in fact, seem to act like the winglets that extend along the tail end of airplane wings during takeoffs and landings. Winglets modify airflow at the tips of wings to help prevent energy loss, which can sometimes be seen as a large contrail following in the wake of some jets.

The upshot of winglets? Effectively longer wings, and more lift for less energy.

The flexible fluke of a dolphin creates a similar increase in lift, and when applied to a variable pitch propeller, the design could increase efficiency to 90 percent (compared to the 70 percent typically associated with standard rotational propellers). Plus, Fish said, the propeller could maintain that efficiency over a much larger range of speeds.

Sizing up an energetic ‘snake’
British researchers have borrowed the moniker of another aquatic creature for their Anaconda Wave Energy Converter, envisioned as a rubber tube running the length of two football fields and undulating with passing waves while tethered to the ocean floor.

The Anaconda, still fairly early in its development, is meant to generate electrical power through the action of successive bulge waves traveling along its length. Each bulge’s movement through the nearly 8-yard diameter tube, at least as depicted in models, is more than a little reminiscent of how you might imagine an unlucky victim makes its way through the digestive tract of a real anaconda, only faster.

Both ends of the water-filled tube are sealed off, with one end facing oncoming waves. When a wave hits and begins squeezing the tube, a bulge wave forms and becomes progressively bigger as it moves forward by the continued squeezing of the sea wave racing along the tube’s outside. At the other end, the bulge wave’s flow turns a turbine and the resulting power zips ashore and feeds the power grid through a cable. If testing continues to pan out, the United Kingdom’s coast could see its first full-scale Anaconda invasion in about five years, with offshore farms of 20 or so tubes capable of powering up to 40,000 homes.

John Chaplin, a professor of applied fluid mechanics at the University of Southampton in the United Kingdom, said Anaconda inventors Francis Farley and Rod Rainey first approached him with their idea a few years ago. Chaplin, who studies the fundamental mechanics of wave forces on structures such as offshore oil and gas installations, was a natural choice and began testing a small-scale version of the tube in 2006.

“There have been ideas around for about 100 years for using waves to generate electricity,” he said. “But in comparison with wind and tidal streams, it has obviously developed much more slowly.”

Engineering challenges
One of the biggest engineering challenges facing the field, he said, is designing something that can survive extremely hostile conditions in the open ocean.

“The variation between the everyday waves that you see and the extreme conditions that exist during a storm that’s raging is very much greater there than the range that wind turbines experience or a tidal stream turbine experiences.”

Of the Anaconda, he said, “we intuitively expect these things to be able to withstand waves much better than steel and concrete and things with hard joints.” The system’s commercial developer, Checkmate SeaEnergy, is likewise betting on it.

But does it work?

In his initial lab tests, Chaplin said, “I could see the bulges traveling pretty much in the way they had envisioned.”

After another two years of models and successful testing of tubes one-twentyfifth the envisioned size, a new grant from the UK’s Engineering and Physical Sciences Research Council will allow Chaplin and Southampton colleague Grant Hearn to direct tests on a model about one-tenth the eventual size —  or about the range of the real anacondas slithering around in South American swamps.

© 2013 msnbc.com Reprints

Discuss:

Discussion comments

,

Most active discussions

  1. votes comments
  2. votes comments
  3. votes comments
  4. votes comments